When shower grout start getting dirty and moldy it needs your quick attention. It could be due to some mishandling at the time of installation or lack of your attention. Some many years old shower tiles look like new and some a year old seems installed 50 years ago. If the grout of your shower is losing, you don’t need to replace it altogether but regrouting shower is another option.
Grout is usually installed in between the tiles. Sometimes it starting falling due to some water leakage behind the tiles and damage of tile backer board. In this case regrouting shower is necessary. But sometimes we use regrouting shower just to give it a new appearance.
Regrouting is the process in which we remove the existing grout out of the space and install the new one. There are many ways to regrout and recaulk the shower one is given under, an easiest one.
First of all, decide your grout color, which matches to the tile of your shower and suits the whole combination. After that clean up your shower tiles with any suitable product and scrub pad that do not scratch your tiles. Mold, rust or soap scum should be removed and cleaned thoroughly before starting regrouting process. Any steam cleaning machine could also prove to be helpful.
The next important step is to clean the old grout out of your shower tiles. Use a sharp tool to lose the grout and remove it but make sure that you are not scratching or damaging the tiles. After removing it clean the space between tiles with a brush so as to make a firm base for new grout.
Now clean up all the mess around you to avoid any disturbance. There may be some mold or wetness so dry the walls and floor before regrouting shower. Never apply grout on wet walls because it will not set in the place.
If you want to replace any damaged tile, do it now.
Now it is time to apply your grout. It is better not to use any ready to use products because they may be of inferior quality. Purchase your grout powder by yourself and mix it according to the prescription given by seller.
Use a grout float and apply grout evenly between the spaces. Fill the joints and remove the excess. With a grout sponge wipe of the tile floor and walls to clean it. The grout takes some time usually 72 hours to cure. Now use a professional sealer to protect your grout from mold and stains. You can see here that regrouting shower is rather easy than you think.
To know how to seal grout, one should take care of some important instructions: firstly, you need to confirm that the grout for tile is set. Then it requires around two days to be dried properly. After getting confirmed about the dryness, the grout sealer is applied. Some makers indicate a waiting period for 6-7 days depending upon the atmosphere and temperature of the location. Some of the major brands of grout sealer in the market suggest a paintbrush, sponge or an applicator for applying seals for grout lines. It all depends on the manufacturer’s directions, which are given over the containing box. Some of the grout sealers are available in the spray form; you can directly apply sealer with comfortable spray box.
The sealer should be applied in a way, that an evenly coated thin layer of seal covers the space in a uniform layer. The grout seal should be applied in a correct method. You should start from very first line of grout. Your movement should be from the left to the right, finally roaming downward. Then start with the next row again in the same direction. While constructing always keep in mind, not to lose your place and concentrate over the portions and places which are left unsealed mistakenly. Lastly sweep off all the extra seal over the grout before drying. The grout sealer should not be left visible over the tiles. Instructions, which are written on the boxes and in manual guides must be read because every brand has its own method and cautions for e.g. some of the sealer brand, are not required to be removed over the tiles. For the best brand, read these grout sealer reviews.
So I believe answer to how to seal grout is not a big task. Once the tile flooring is laid, the sealing of grout is a very important step to be taken care of. We need to work on the moisture and dirt sections. Applying the seals to make floor more resistant to the dirt and liquids. The grout which remains unsealed absorbs the dirt, grunge and stains. It becomes very difficult to clean the unsealed floor. If the tiles are vitreous, then the sealing of the grout is a necessity. Both, the colored and natural grout gets on to the tile and holds the edges of the tile tightly, acting like glue. The sealing of grout safeguards and protects the grout naturally.